Forum KajKupiti

Joza napisal/-a: ↑

12 Jan 2023, 17:21

Pozdravljeni, sin si zeli 3d tiskalnik. Se morda kdo spozna kaj na zadevo, predvsem na kaj je potrebno biti pozoren pri posameznih modelih? Thomson morda kaksen popust ...hvala lp

Joza napisal/-a: ↑

13 Jan 2023, 12:09

Ja budget je tam do 300 eur, razen ce je za kaksnega res boljsega, potem bi se lahko Malo stisnil...

• Flashforge Adventurer 3 Lite 3D tiskalnik s kodo: NNNDBDHJSG iz 300€ na 239€ (EU)

• Flashforge Adventurer 3 3D tiskalnik s kodo: KAJKUPITI za 323€ (EU)

• Creality Ender 3 S1 3D tiskalnik s kodo: KAJKUPITI za 309€ (EU)

• Creality Ender 3 S1 Pro 3D tiskalnik s kodo: CREALITH9TH4 za 382€ (EU)

• Anycubic Kobra 3D tiskalnik s kodo: GKB3D26 iz 281€ na 249€ (EU)

• AnkerMake M5 3D tiskalnik v akciji iz 849€ na 599€
  (Anker.si, Slo trgovina, Slo garancija, 1-2 dni dostava)

conquer napisal/-a: ↑

13 Nov 2023, 22:40

Zdravo, eno hitro vprašanje, je Ender 3 v3 SE vreden nakup za 170€ oz. kar me bolj zanima, če je primerljiv z obstoječim Ender 3 v2 printerjem, katerega si trenutno lastim? Hvala in lep pozdrav.

The Ender 3 V3 SE is the most affordable Creality 3D printer yet to include a direct-drive extruder, which is a substantial upgrade over the Bowden extruder on the Ender 3 V2 . The Ender 3 V3 SE’s extruder is the same Creality Sprite extruder that we’ve seen on other machines such as the Ender 3 S1, and we’re excited to see this feature make it into an entry-level machine.This is the most meaningful upgrade on the Ender 3 V3 SE. Compared to the Ender 3 V2, you’ll see higher reliability, faster print speeds, and an improved ability to print flexible filament on the Ender 3 V3 SE.

While both printers use CR-touch auto leveling, the Ender 3 V3 SE added a very clever secondary system for calibrating the Z offset of the printer automatically. On previous models, part of the setup required you to adjust the print head until the nozzle was slightly above the bed, and then save the offset so that the nozzle is the correct height after the auto leveling. The Ender 3 V3 uses a strain sensor on the bed to measure the actual position of the nozzle by gently touching it to the bed. Using this data, it can set the Z offset automatically. This feature will allow you to use different bed materials of different thicknesses with minimal effort.

The firmware on the Ender 3 V3 SE supports much higher acceleration settings than previous Creality printers, allowing for much faster print speeds. The default acceleration is set to 4000 mm/s, as compared to 1000 maximum on the Ender 3 V2. We tested a benchy at a high speed setting (30 minute print time) and were quite impressed with the near perfect quality despite the speed. Creality advertises capability of up to 250 mm/s, which is 5x typical printing speeds, but we saw some slippage when testing at this speed. However, the max speed we achieved of 175 mm/s is still very impressive and faster than what is possible on the S1 without firmware updates. We do think similar speeds are achievable on the Ender 3 V2 since there are no hardware differences, but it would require updating the firmware to unlock higher acceleration settings.

The display and user interface on the Creality Ender 3 V3 SE are improved compression to the Ender 3 V2 Neo. While the controls are similar—both printers use a jog wheel with a button to navigate the menus—the Ender 3 V3 SE’s screen can display more colors and includes more information than what you get on the Ender 3 V2 Neo. In many ways, the improved display is simply a nice-to-have feature that makes the Ender 3 V3 SE feel more polished and modern. However, there are a few benefits you may appreciate. For example, the Ender 3 V3 SE displays a graph of the current hotend temperature, allowing you to monitor the temperature more easily than the simpler numbers-only display found on many other printers. Other features such as the automatic bed leveling, also benefit from the improved interface by being able to display more detailed information. This isn’t a major difference between the machines, but we give the edge to the Ender 3 V3 SE here because the interface displays more information and displays it more clearly than the Ender 3 V2 Neo.

Perhaps a more difficult question is whether you should upgrade from an existing Ender 3 V2 Neo to the Ender 3 V3 SE. There’s no doubt that the SE is a better machine, but these two printers are close enough in price and base features that you may be better off installing the Creality Sprite extruder upgrade kit. We’ve reviewed a similar kit and have found it to be reliable and a great improvement on older printers.

conquer napisal/-a: ↑

14 Nov 2023, 23:13

Hvala ti za pomoč. Seveda ne nameravam menjat obstoječega in precej "naloadanga" v2 modela, mi še vedno dobro služi Iščem printer za začetnika in po prebranih primerjavah menim, da bo V3 SE super vstopni model.Lahko še svetuješ kje se dobi najugodnejše filamente? Hvala.

• Creality Ender-3 V3 SE 3D tiskalnik s kodo: 88FNK6SBYM za 169€ (EU)